10.3 Inch IPS LVDS Stretched Bar LCD Module for Embedded HMI

10.3 Inch IPS LVDS Stretched Bar LCD Module for Embedded HMI

Built for slim interface layouts, this 10.3-inch IPS panel pairs a 1920 × 720 canvas with a matched LVDS controller board for faster evaluation.

Product Summary

The IPS LVDS Stretched Bar LCD Module combines a 10.3-inch panoramic TFT-LCD with 1920 × 720 resolution, 850 cd/m² typical luminance and a controller-board path for development and system evaluation. Its 243.6 × 91.4 mm active area fits long interface zones where standard 16:9 panels can consume unnecessary vertical space.

The panel uses IPS Pro, normally black, transmissive operation with a 1000:1 typical contrast ratio and 85°/85°/85°/85° typical viewing angles in confirmed left/right/up/down order. The display signal is a 50-pin, two-channel, 8-bit LVDS connection, while the controller board provides a separate input and power domain.

Key Specifications

Native 1920 × 720 Panoramic Layout

Long-format UI without excessive panel height

The native 1920 × 720 raster gives interface designers a broad horizontal canvas for status zones, timelines, machine information, segmented controls and branded visual bands. Using the native raster avoids scaling artifacts and lets the UI match the physical proportions of the display.

Active-area planning for enclosure design

The 243.6 × 91.4 mm active area sits within a 262.04 × 110.3 × 8.4 mm panel outline. Enclosure drawings should distinguish the visible image area from the full module envelope and preserve clearance for the signal cable and controller-board assembly.

Optical Performance for Bright Indoor Equipment

850 cd/m² typical luminance

The 850 cd/m² typical panel rating provides a stronger luminance level than many standard embedded indoor panels. It is useful where the screen operates under bright commercial or equipment-room lighting and the UI must remain visually prominent.

An 850 cd/m² panel rating does not by itself establish direct-sun readability or weatherproof outdoor operation.

IPS Pro viewing behavior

The panel specifies 85°/85°/85°/85° typical viewing in left/right/up/down order at CR ≥ 10. This is useful for equipment that may be viewed from several operator positions or installed below or above normal eye level.

IPS LVDS Stretched Bar LCD Module Integration

Verify the complete 50-pin LVDS definition

The panel uses a two-channel, 8-bit LVDS interface through a 50-pin connector. Matching the connector count is only the first compatibility check; the complete pin assignment, channel mapping, timing, clocking, power pins and connector orientation still need to match the intended host or controller.

A 50-pin LVDS connector does not guarantee compatibility with another 50-pin LCD panel.

Use the matched controller path for evaluation

The supplied kit includes a controller board, converter board, signal cable and keypad cable, giving developers a practical evaluation path before a custom host design is finalized. For a production design, the controller-board revision and cable set should be locked against the approved sample rather than assumed from a generic LVDS label.

Power Architecture and Controller Board

Keep panel and controller power domains separate

The LCD panel specifies 3.3 V typical input, while the controller-board assembly requires a 12 V DC adapter capable of more than 2 A.

The 3.3 V panel input and the 12 V DC controller input are separate power requirements.

The controller standby figure is below 1 W, but that value does not define the maximum operating power of the complete display kit.

Standby power below 1 W is not the maximum operating power of the complete assembly.

Confirm the production controller revision

The kit information uses closely related controller revision labels. Before volume production, confirm the exact controller board, firmware, host-input configuration and cable set on the approved sample so that mechanical and electrical documentation remain aligned.

Mechanical Integration and Cable Clearance

Panel and board dimensions must both fit

The panel outline is 262.04 × 110.3 × 8.4 mm, and the controller board is 85 × 54 × 14 mm. A finished enclosure must accommodate both components plus the converter board, LVDS cable routing, keypad lead and connector access.

The IPS LVDS Stretched Bar LCD Module is therefore best treated as a panel-and-controller integration package during prototype planning, even when the final product may later use a custom controller architecture.

Included Kit Scope and Configuration Boundaries

Included evaluation components

The kit contains the 10.3-inch 1920 × 720 LCD, controller board, converter board, signal cable and keypad with cable. The controller supports a digital video/audio input path and speaker or earphone audio output.

Touch capability is not confirmed for this configuration and should be treated as a separate project requirement rather than assumed from the screen format.

Custom project review

Cable definition, controller revision, enclosure adaptation, front cover, optical treatment, mounting and alternate controller requirements can be reviewed by project. Custom configurations are generally reviewed from 500 pieces, subject to tooling requirements, material availability and the requested specification. Sample and standard-kit quantities are confirmed separately.

Application Fit for Embedded HMI and Information Panels

This display format suits embedded HMI prototypes, equipment status panels, horizontal control strips, compact information interfaces and commercial device concepts that need a wide image area without a tall enclosure.

For projects already designed around a standard 16:9 panel, the IPS LVDS Stretched Bar LCD Module should be selected only after the native 1920 × 720 UI layout, host output, cable routing and enclosure opening have been validated together.

Procurement Checklist

Before approving the IPS LVDS Stretched Bar LCD Module, confirm the native 1920 × 720 timing, complete 50-pin LVDS map, two-channel 8-bit configuration, connector orientation, 3.3 V panel input, backlight electrical requirements, 12 V controller supply, exact controller revision, 243.6 × 91.4 mm active area, 262.04 × 110.3 × 8.4 mm panel fit, 85 × 54 × 14 mm board clearance, front-cover optical target, touch requirement, sample quantity and annual demand.